Solar Power

Solar power is the technology of obtaining usable energy from the light of the Sun. Solar energy has been used in many traditional technologies for centuries and has come into widespread use where other power supplies are absent, such as in remote locations and in space.

Solar energy is currently used in a number of applications:

Heat (hot water, building heat, cooking)
Electricity generation (photovoltaics, heat engines)
Desalination of seawater.

Energy from the Sun

Solar radiation reaches the Earth's upper atmosphere at a rate of 1366 watts per square meter (W/m2). The first map shows how the solar energy varies in different latitudes.

While traveling through the atmosphere 6% of the incoming solar radiation (insolation) is reflected and 16% is absorbed resulting in a peak irradiance at the equator of 1,020 W/m². Average atmospheric conditions (clouds, dust, pollutants) further reduce insolation by 20% through reflection and 3% through absorption. Atmospheric conditions not only reduce the quantity of insolation reaching the earth's surface but also affect the quality of insolation by diffusing incoming light and altering its spectrum.

The second map shows the average global irradiance calculated from satellite data collected from 1991 to 1993. For example, in North America the average insolation at ground level over an entire year (including nights and periods of cloudy weather) lies between 125 and 375 W/m² (3 to 9 kWh/m²/day). This represents the available power, and not the delivered power. At present, photovoltaic panels typically convert about 15% of incident sunlight into electricity; therefore, a solar panel in the contiguous United States on average delivers 19 to 56 W/m² or 0.45 - 1.35 (kW·h/m²)/day.

The dark disks in the third map on the right are an example of the land areas that, if covered with 8% efficient solar panels, would produce slightly more energy in the form of electricity than the total world primary energy supply in 2003. While average insolation and power offer insight into solar power's potential on a regional scale, locally relevant conditions are of primary importance to the potential of a specific site.

After passing through the Earth's atmosphere, most of the sun's energy is in the form of visible and Infrared radiations. Plants use solar energy to create chemical energy through photosynthesis. Humans regularly use this energy burning wood or fossil fuels, or when simply eating the plants.

A recent concern is global dimming, an effect of pollution that is allowing less sunlight to reach the Earth's surface. It is intricately linked with pollution particles and global warming, and it is mostly of concern for issues of global climate change, but is also of concern to proponents of solar power because of the existing and potential future decreases in available solar energy. The order of magnitude is about 4% less solar energy available at sea level over the timeframe 1961–90, mostly from increased reflection from clouds back into outer space.

Types of technologies
Many technologies have been developed to make use of solar radiation. Some of these technologies make direct use of the solar energy (e.g. to provide light, heat, etc.), while others produce electricity.

Solar design in architecture
Main article: Passive solar building design
Solar design in architecture involves the use of appropriate solar technologies to maintain a building’s environment at a comfortable temperature through the sun's daily and annual cycles. It may do this by storing solar energy as heat in the walls of a building, which then acts to heat the building at night. Another approach is to keep the interior cool during a hot day by designing in natural convection through the building’s interior.

Solar heating systems
Main articles: Solar hot water and Solar combisystem
Solar hot water systems use sunlight to heat water. They may be used to heat domestic hot water, for space heating or to heat swimming pools. These systems are composed of solar thermal collectors, a storage tank and a circulation loop. The three basic classifications of solar water heaters are:

Batch systems which consist of a tank that is directly heated by sunlight. These are the oldest and simplest solar water heater designs, however; the exposed tank can be vulnerable to cooldown.
Active systems which use pumps to circulate water or a heat transfer fluid.
Passive systems which circulate water or a heat transfer fluid by natural circulation. These are also called thermosiphon systems.

A Trombe wall is a passive solar heating and ventilation system consisting of an air channel sandwiched between a window and a sun-facing wall. Sunlight heats the air space during the day causing natural circulation through vents at the top and bottom of the wall and storing heat in the thermal mass. During the evening the Trombe wall radiates stored heat.

A transpired collector is an active solar heating and ventilation system consisting of a perforated sun-facing wall which acts as a solar thermal collector. The collector pre-heats air as it is drawn into the building's ventilation system through the perforations. These systems are inexpensive and commercial models have achieved efficiencies above 70%. Most systems pay for themselves within 4-8 years.

Solar cooking
Main article: Solar cooker

Solar Cookers use sunshine as a source of heat for cooking as an alternative to fire.A solar box cooker traps the sun's energy in an insulated box; such boxes have been successfully used for cooking, pasteurization and fruit canning. Solar cooking is helping many developing countries, both reducing the demands for local firewood and maintaining a cleaner breathing environment for the cooks.

The first known western solar oven is attributed to Horace de Saussure in 1767, which impressed Sir John Herschel enough to build one for cooking meals on his astronomical expedition to the Cape of Good Hope in Africa in 1830. Today, there are many different designs in use around the world.

Solar lighting
Main articles: Daylighting and Light tube
Solar lighting or daylighting is the use of natural light to provide illumination. Daylighting directly offsets energy use in electric lighting systems and indirectly offsets energy use through a reduction in cooling load. Although difficult to quantify, the use of natural light also offers physiological and psychological benefits.

Daylighting features include building orientation, window orientation, exterior shading, sawtooth roofs, clerestory windows, light shelves, skylights and light tubes. These features may be incorporated in existing structures but are most effective when integrated in a solar design package which accounts for factors such as glare, heat gain, heat loss and time-of-use. Architectural trends increasingly recognize daylighting as a cornerstone of sustainable design.

Daylight saving time (DST) can be seen as a method of utilising solar energy by matching available sunlight to the hours of the day in which it is most useful. DST energy savings have been estimated to reduce total electricity use in California by 0.5% (3400 MWh) and peak electricity use by 3% (1000 MW).[16] However, there is some question whether these estimates are valid. In 2000 when parts of Australia began DST in late winter, overall electricity consumption did not decrease, but the peak load increased.

Photovoltaics
Main article: Photovoltaics

The solar panels (photovoltaic arrays) on this small yacht at sea can charge the 12 V batteries at up to 9 A in full, direct sunlightSolar cells, also referred to as photovoltaic cells, are devices or banks of devices that use the photovoltaic effect of semiconductors to generate electricity directly from sunlight. Until recently, their use has been limited because of high manufacturing costs. One cost effective use has been in very low-power devices such as calculators with LCDs. Another use has been in remote applications such as roadside emergency telephones, remote sensing, cathodic protection of pipe lines, and limited "off grid" home power applications. A third use has been in powering orbiting satellites and spacecraft.

Total peak power of installed PV is around 1,700 MW as of the end of 2005. This is only one part of solar-generated electric power.

Declining manufacturing costs (dropping at 3 to 5% a year in recent years) are expanding the range of cost-effective uses. The average lowest retail cost of a large photovoltaic array declined from $7.50 to $4 per watt between 1990 and 2005. With many jurisdictions now giving tax and rebate incentives, solar electric power can now pay for itself in five to ten years in many places. "Grid-connected" systems - those systems that use an inverter to connect to the utility grid instead of relying on batteries - now make up the largest part of the market.

In 2003, worldwide production of solar cells increased by 32%.[20] Between 2000 and 2004, the increase in worldwide solar energy capacity was an annualized 60%.[21] 2005 was expected to see large growth again, but shortages of refined silicon have been hampering production worldwide since late 2004. Analysts have predicted similar supply problems for 2006 and 2007.

Solar thermal electric power plants

Solar Two, a concentrating solar power tower (an example of solar thermal energy applied to electrical power production).Main article: Solar thermal energy
Solar thermal energy can be focused on a heat exchanger, and converted in a heat engine to produce electric power or applied to other industrial processes.

Power towers
Main article: Solar power tower
Power towers use an array of flat, movable mirrors (called heliostats) to focus the sun's rays upon a collector tower (the target). The high energy at this point of concentrated sunlight is transferred to a working fluid for conversion to electrical energy in a heat engine, or in some instances, stored for nighttime usage, in order to provide a more continuous output.

Parabolic troughs
Main article: Parabolic trough
A long row of parabolic mirrors concentrates sunlight on a tube filled with a heat transfer fluid (usually oil). As with the power tower, this heated oil is used to power a conventional steam turbine, or stored for nighttime use. The largest operating solar power plant, as of 2007, is one of the SEGS parabolic trough systems in the Mojave Desert in California, USA.

Concentrating collector with steam engine
Solar energy converted to heat in a concentrating collector can be used to boil water into steam (as is done in nuclear and coal power plants) to drive a steam engine or steam turbine. The concentrating collector can be a trough collector, parabolic collector, or power tower.

Concentrating collector with Stirling engine

A parabolic solar collector concentrating the sun's rays on the heating element of a Stirling engine. The entire unit acts as a solar tracker.Solar energy converted to heat in a concentrating (dish or trough parabolic) collector can be used to drive a Stirling engine, a type of heat engine which uses a sealed working gas (i.e. a closed cycle) and does not require a water supply.

Until recently, a solar Stirling system held the record for converting solar energy into electricity (30% at 1,000 watts per square meter).[24] Such concentrating systems produce little or no power in overcast conditions and incorporate a solar tracker to point the device directly at the sun. That record has been broken by a so-called concentrator solar cell produced by Boeing-Spectrolab which claims a conversion efficiency of 40.7 percent.

Solar updraft tower
Main article: Solar updraft tower
A solar updraft tower (also known as a solar chimney, but this term is avoided by many proponents due to its association with fossil fuels) is a relatively low-tech solar thermal power plant where air passes under a very large agricultural glass house (between 2 and 8 km in diameter), is heated by the sun and channeled upwards towards a convection tower. It then rises naturally and is used to drive turbines, which generate electricity.

Energy tower
An energy tower is an alternative proposal to the solar updraft tower. It is driven by spraying water at the top of the tower, evaporation of water causes a downdraft by cooling the air thereby increasing its density, driving wind turbines at the bottom of the tower. It requires a hot arid climate and large quantities of water (seawater may be used) but does not require the large glass house of the solar updraft tower.

Solar pond
A solar pond is simply a pool of water which collects and stores solar energy. It contains layers of salt solutions with increasing concentration (and therefore density) to a certain depth, below which the solution has a uniform high salt concentration. It is a relatively low-tech, low-cost approach to harvesting solar energy. The principle is to fill a pond with 3 layers of water:

A top layer with a low salt content.
An intermediate insulating layer with a salt gradient, which sets up a density gradient that prevents heat exchange by natural convection in the water.
A bottom layer with a high salt content which reaches a temperature approaching 90 degrees Celsius.
The layers have different densities due to their different salt content, and this prevents the development of convection currents which would otherwise transfer the heat to the surface and then to the air above. The heat trapped in the salty bottom layer can be used for heating of buildings, industrial processes, generating electricity or other purposes. One such system is in use at Bhuj, Gujarat, India[26] and another at the University of Texas El Paso.

Solar chemical
Solar chemical is any process that harnesses solar energy by absorbing sunlight in a chemical reaction in a way similar to photosynthesis in plants but without using living organisms. No large-scale systems have as yet been constructed.

Another chemical (but not photochemical) approach has been to use conventional solar thermal collectors to drive chemical dissociation reactions. Ammonia can be separated into nitrogen and hydrogen at high temperature and with the aid of a catalyst, stored indefinitely, then recombined later to release the heat stored. A prototype system was constructed at the Australian National University.

A promising approach is to use focused sunlight to provide the energy needed to split water into its constituent hydrogen and oxygen in the presence of a metallic catalyst such as zinc.

While metals, such as zinc, have been shown to drive photoelectrolysis of water, more research has focused on semiconductors. Further research has examined transition metal compounds, in particular titanium, niobium and tantalum oxides.

Unfortunately, these materials exhibit very low efficiencies, because they require ultraviolet light to drive the photoelectrolysis of water. Current materials also require an electrical voltage bias for the hydrogen and oxygen gas to evolve from the surface, another disadvantage. Current research is focusing on the development of materials capable of the same water splitting reaction using lower energy visible light.

It is also possible to use solar energy to drive industrial chemical processes without a requirement for fossil fuel.

Classifications of solar power technology
Solar power technologies can be classified in a number of ways.

Photovoltaic cells produce electricity directly from sunlight
Direct or Indirect
In general, direct solar power involves a single transformation of sunlight which results in a usable form of energy.

Sunlight hits a photovoltaic cell creating electricity.
Sunlight warms a thermal mass.
Sunlight strikes a solar sail on a space craft and is converted directly into a force on the sail which causes motion of the craft.
Sunlight strikes a light mill and causes the vanes to rotate as mechanical energy, little practical application has yet been found for this effect.
In a direct solar water heater the water heated in the collector is used in the domestic water system.

In general, indirect solar power involves multiple transformations of sunlight which result in a usable form of energy.

Vegetation uses photosynthesis to convert solar energy to chemical energy. The resulting biomass may be burned directly to produce heat and electricity or processed into ethanol, methane, hydrogen and other biofuels.
Hydroelectric dams and wind turbines are powered by solar energy through its interaction with the Earth's atmosphere and the resulting weather phenomena.
Ocean thermal energy production uses the thermal gradients present across ocean depths to generate power. These temperature differences are produced by sunlight.
Fossil fuels are ultimately derived from solar energy captured by vegetation in the geological past.
In an indirect solar water heater the fluid heated in the collector transfers its heat through a heat exchanger to a separate domestic water system.

Passive or active
This distinction is made in the context of building construction and building services engineering.

Passive solar systems use non-mechanical techniques of capturing, converting and distributing sunlight into usable outputs such as heating, lighting or ventilation. These techniques include selecting materials with favorable thermal properties, designing spaces that naturally circulate air and referencing the position of a building to the sun.

Passive solar water heaters use a thermosiphon to circulate fluid.
A Trombe wall circulates air by natural circulation and acts as a thermal mass which absorbs heat during the day and radiates heat at night.
Clerestory windows, light shelves, skylights and light tubes can be used among other daylighting techniques to illuminate a building's interior.
Passive solar water distillers may use capillary action to pump water.
Active solar systems use electrical and mechanical components such as photovoltaic panels, pumps and fans to process sunlight into usable outputs.

Concentrating or non-concentrating

A large parabolic reflector solar furnace is located in the Pyrenees at Odeillo, French Cerdagne. It is used for various research purposes.Concentrating solar power (CSP) systems use lenses or mirrors and tracking systems to focus a large area of sunlight into a small beam capable of producing high temperatures and correspondingly high thermodynamic efficiencies. Concentrating solar is generally associated with solar thermal applications but concentrating photovoltaic (CPV) applications exist as well and these technologies also exhibit improved efficiencies. CSP systems require direct insolation to operate properly.

Concentrating solar power systems vary in the way they track the sun and focus light.

Line focus/Single-axis
A solar trough consists of a linear parabolic reflector which concentrates light on a receiver positioned along the reflector's focal line. These systems use single-axis tracking to follow the sun. A working fluid (oil, water) flows through the receiver and is heated up to 400 °C before transferring its heat to a distillation or power generation system.[34][35] Trough systems are the most developed CSP technology. The Solar Electric Generating System (SEGS) plants in California and Plataforma Solar de Almería's SSPS-DCS plant in Spain are representatives of this technology.
Point focus/Dual-axis
A power tower consists of an array of flat reflectors (heliostats) which concentrate light on a central receiver located on a tower. These systems use dual-axis tracking to follow the sun. A working fluid (air, water, molten salt) flows through the receiver where it is heated up to 1000 °C before transferring its heat to a power generation or energy storage system. Power towers are less advanced than trough systems but they offer higher efficiency and energy storage capability. The Solar Two in Daggett, California and the Planta Solar 10 (PS10) in Sanlucar la Mayor, Spain are representatives of this technology.
A parabolic dish or dish/engine system consists of a stand-alone parabolic reflector which concentrates light on a receiver positioned at the reflector's focal point. These systems use dual-axis tracking to follow the sun. A working fluid (hydrogen, helium, air, water) flows through the receiver where it is heated up to 1500 °C before transferring its heat to a sterling engine for power generation. Parabolic dish systems display the highest solar-to-electric efficiency among CSP technologies and their modular nature offers scalability. The Stirling Energy Systems (SES) and Science Applications International Corporation (SAIC) dishes at UNLV and the Big Dish in Canberra, Australia are representatives of this technology.
Non-concentrating photovoltaic and solar thermal systems do not concentrate sunlight. While the maximum attainable temperatures (200 °C) and thermodynamic efficiencies are lower, these systems offer simplicity of design a have the ability to effectively utilize diffuse insolation. Flat-plate thermal and photovoltaic panels are representatives of this technology.

Advantages and disadvantages of solar power

US annual average solar energy received by a latitude tilt photovoltaic cell.
Advantages
The 89 petawatts of sunlight reaching the earth's surface is plentiful compared to the 15 terawatts of average power consumed by humans.[39] Additionally, solar electric generation has the highest power density (global mean of 170 W/m2) among renewable energies.
Solar power is pollution free during use. Production end wastes and emissions are manageable using existing pollution controls. End-of-use recycling technologies are under development.[40]
Facilities can operate with little maintenance or intervention after initial setup.[citation needed]
Solar electric generation is economically competitive where grid connection or fuel transport is difficult, costly or impossible. Examples include satellites, island communities, remote locations and ocean vessels.
When grid connected, solar electric generation can displace the highest cost electricity during times of peak demand (in most climatic regions), can reduce grid loading, and can eliminate the need for local battery power for use in times of darkness and high local demand; such application is encouraged by net metering. Time-of-use net metering can be highly favorable to small photovoltaic systems.
Grid connected solar electricity can be used locally thus minimizing transmission/distribution losses (approximately 7.2%).
Once the initial capital cost of building a solar power plant has been spent, operating costs are low when compared to existing power technologies.).

Disadvantages
Polysilicon Solar cells are costly, requiring a large initial capital investment, and silicon shortages raise prices. Costs are expected to come down, however, due to increased manufacturing, economies of scale and Balance of System planning. Thin film technology uses less silicon; and Lease/Rental options* are currently being introduced.
Limited power density: Average daily insolation in the contiguous U.S. is 3-9 kW·h/m2 usable by 7-17.7% efficient solar panels.
To get enough energy for larger applications, a large number of photovoltaic cells is needed. This increases the cost of the technology and requires a large plot of land.
Like electricity from nuclear or fossil fuel plants, it can only realistically be used to power transport vehicles by converting light energy into another form of stored energy (e.g. battery stored electricity or by electrolysing water to produce hydrogen) suitable for transport.
Solar cells produce DC which must be converted to AC when used in currently existing distribution grids. This incurs an energy loss of 4-12%.

Availability of solar energy
There is no shortage of solar-derived energy on Earth. Indeed the storages and flows of energy on the planet are very large relative to human needs.

The amount of solar energy intercepted by the Earth every minute is greater than the amount of energy the world uses in fossil fuels each year.
Tropical oceans absorb 560 trillion gigajoules (GJ) of solar energy each year, equivalent to 1,600 times the world’s annual energy use.
The energy in the winds that blow across the United States each year could produce more than 16 billion GJ of electricity—more than one and one-half times the electricity consumed in the United States in 2000.
Annual photosynthesis by the vegetation in the United States is 50 billion GJ, equivalent to nearly 60% of the nation’s annual fossil fuel use.

Plants, on average, capture 0.1% of the solar energy reaching the Earth. The land area of the lower 48 United States intercepts 50 trillion GJ per year, equivalent to 500 times of the nation’s annual energy use.[51] This energy is spread over 8 million square kilometers of land area, so that each square meter is exposed to 6.1 GJ per year. This results in potential biomass production of 6,100 GJ per square kilometer per year. Compared to the 0.1% efficiency of vegetation, roof installable amorphous silicon solar panels capture 8%-14% of the solar energy, while more expensive crystalline panels capture 14%-20%, and large scale desert mirror-concentrator heat engine based setups may capture up to 30-50%.

Energy storage
Main article: Grid energy storage
For a stand-alone system, some means must be employed to store the collected energy for use during hours of darkness or cloud cover. The following list includes both mature and immature techniques:

Using traditional batteries
Thermal mass
Pumped-storage hydroelectricity
Flow batteries
Molten salt
Cryogenic liquid air or nitrogen
Compressed air in cylinders and in caverns
Flywheel energy storage
Hydrogen produced by electrolysis
Hydraulic accumulator
Superconducting magnetic energy storages
Vegetable oil economy
Storage always has an extra stage of energy conversion, with consequent energy losses, increasing the total capital costs. One way around this is to export excess power to the power grid, drawing it back when needed. This appears to use the power grid as a battery but in fact is relying on conventional energy production through the grid during the night. However, since the grid always has a positive outflow, the result is exactly the same.

Electric power costs are highly dependent on the consumption per time of day, since plants must be built for peak power (not average power). Expensive gas-fired "peaking generators" must be used when base capacity is insufficient. Fortunately for solar, solar capacity parallels energy demand -since much of the electricity is for removing heat produced by too much solar energy (ie, air conditioners). This is less true in the winter. Wind power complements solar power since it can produce energy when there is no sunlight.

Deployment of solar power

The solar powered car The Nuna 3 built by the Dutch Nuna teamMain article: Deployment of solar power to energy grids
Deployment of solar power depends largely upon local conditions and requirements. All industrialised nations share a need for electricity and it is believed that solar power will increasingly be used as an option for electricity supply.

Solar Power By Country

Australia
Main article: Solar power in Australia
A $420 million large-scale Solar power station in Victoria is to be the biggest and most efficient solar photovoltaic power station in the world. Australian company Solar Systems will demonstrate its unique, world leading design incorporating space technology in a 154MW solar power station connected to the national grid. The power station will have the capability to concentrate the sun by 500 times onto the solar cells for ultra high power output. The Victorian power station will generate clean electricity directly from the sun to meet the annual needs of over 45,000 homes with zero greenhouse gas emissions.

Solar powered car
Development of a practical solar powered car has been an engineering goal for 20 years. The center of this development is the World Solar Challenge, a biannual solar powered car race over 3021 km (1877mi) through central Australia from Darwin to Adelaide. The race's stated objective is to promote research into solar-powered cars. Teams from universities and enterprises participate. In 1987 when it was founded, the winner's average speed was 67 km/h (42 mph).[53] By the 2005 race this had increased to an average speed of greater than 100 km/h (62 mph), even though the cars were faced with the 110 km/h (68 mph) South Australia speed limit. (Credit: Wikipedia).